Waterproofing Chemical

Product Details:

Description
Nitoflor Hardtop Standard is quality controlled, factory blended powder which are ready to use on site. They contain special quartz-silica aggregates which have been selected for abrasion and wear resistant properties as well as shape and size. These latter considerations, together with the use of high performance workability admixtures, produces a material which is easy to trowel into the surface of fresh, wet concrete. Nitofl or Hardtop Standard cure monolithically to provide a dense, non-porous surface which is extremely hardwearing and abrasion resistant. Monolithic cure ensures that problems normally associated with thin ‘granolithic’ screeds, viz., shrinkage, cracking, etc., are completely overcome. Being non-metallic, Nitofl or Hardtop Standard provide a nonslip surface which will never rust and disintegrate

Product Details:

CICO SUPER

Normal setting liquid integral waterproofing compound for concrete and mortar. Available with ISI mark IS 2645:2003

Features :-

•       Permeability of concrete is greatly reduced, acts as a hydrophobe

•       Increases cohesion, reduces segregation and bleeding significantly.

•       Improves workability and surface finish of concrete and mortar.

Usage :-

RCC/ plain concrete intended for water  tank, roof slab, basement, lift pit or in a situation where hydro insulation is a must.

Method of Application :-

Add measured quantity of CICO Super to mixing water. Add solution only into the dry mix of cement and sand. The quantity of CICO Super and water is to be pre-determined as per the cement content of the mix.

Dosage :-  0.2% or 100ml per bag  of cement

Pack Size :-  100ml, 1ltr, 5ltr, 10ltr, 20ltr, 50ltr and 200ltr plastic container

Shelf Life :- 18 months

Product Details:

Cico Tapecrete Waterproofing Chemical 
P151, popularly known as Tapecrete is an acrylic based Polymer Modified Cementations Flexible Composite coating system. Tapecrete, in conjunction with cement, makes up for the shortcomings of plain cement, particularly its poor adhesion properties, low impact strength, low flexural strength and thin section fragility. Tapecrete Polymer enhances qualities of cement slurry/ mortar/concrete making them excellent choices for use in new constructions as well as for renovation work.

Product Details:

• Provide a tough, flexible, hard-wearing surface with waterproofing
• Allows trapped vapour to escape, preventing peeling and blistering
• Can be applied with uniform thickness to horizontal and vertical surfaces
• Develops excellent bond with most building materials
• Reduces or prevents salt penetration into concrete
• Is not affected by ultraviolet light or by chemicals ranging from mild acids to those that are strongly alkaline.
• Is highly durable in continuously wet conditions
• Is non-flammable and does not emit toxic gases, when exposed to fire
• Will not rot or corrode
• Most properties improve with age
• Is not harmful to the health of workmen
• Acrylic Polymer for cement composite and its multipurpose uses

Product Details:

Polyester and polyproplene fibre 6mm for plaster 12mm for flooringRecron® 3s is a state of art reinforcing material which is used to increase strength

Product Details:

Features:

• Sika® Injection-201 CE is a very low viscous, elastic and solvent-free polyurethane injection resin. In contact with water, a uniform, closed and therefore watertight pore structure forms, which is elastic and flexible. 
• Permanently elastic, can absorb limited movements
• No shrinkage in subsequent dry conditions
• Due to its low viscosity it can penetrates into cracks >0.2 mm in width
• Cured Sika® Injection-201 CE is inert and chemically-resistant
• Solvent-free, environmentally friendly, usable in ground water protection zones
• In cold temperatures (< +10°C) Sika® Injection-201 CE can be accelerated using Sika® Injection-AC20
• Can be injected as a one component system (when no accelerator is used) 
• Sika® Injection-201 CE is used for permanent watertight sealing with some flexibility to absorb limited movement, in dry, damp or water-bearing cracks and joints in concrete, brickwork and natural stone
• Sika® Injection-201 CE can be used for the injection of the Sika® Fuko System (non re-injectable!)
• For use in water-bearing cracks under hydrostatic pressure, preliminary injection with shall be made with Sika® Injection-101RC 

Product Details:

ShaliUrethane® LHM is single component, high tensile, high solid, moisture cured, modified Polyurethane elastomeric liquid membrane for waterproofing with an elongation of 700 % ± 50. ShaliUrethane® LHM forms a seamless monolithic membrane by reaction with atmospheric moisture. It conforms to ASTM C-836 and ASTM C-898.

Product Details:

White Liquid Dr Fixit Lw Plus Waterproofing Chemicals, For Concrete Surface, Coverage: 27-28sqft Per Liter. Dr. Fixit Fastflex is a two component acrylic cementitious coating system for waterproofing of wet areas and any water retaining structures such as swimming pools and water features. It provides strong bonding and excellent resistant to hydrostatic water pressure by forming highly elastic seamless coating over the applied concrete surfaces.

Additional Information:

• Delivery Time: immediate
• Packaging Details: 48kg

Product Details:

Reebaklens RR is used as a rust remover from steel bars prior to encasing in concrete / microconcrete. It can also be used on ohter steel surfaces prior to coating with epoxy systems.

Additional Information:

• Item Code: immeidate
• Production Capacity: 100
• Delivery Time: ontime
• Packaging Details: 1ltr,20ltr.

Product Details:

STARPROOF WF-SP-600 is a special synthetic resin based waterproof coating. Because of its excellent flexibility and thixotropic nature it is ideal for use on vertical as well as horizontal surfaces. It is single pack, very economical and pollution free water proof coating. Due to its white color, it offers excellent UV Resistance & Solar reflectivity. Gives cooling effect due to the reflective properties.

Additional Information:

• Production Capacity: (15/30 mm gauge)
• Delivery Time: all time
• Packaging Details: STARPROOF WF-SP-600 is available in 20 kg. pail, 200 kg. metal drum.

Product Details:

Shrinkage controlled, polymer modified, cementitious repair mortar, specifically designed for spraying Uses Renderoc SP40 is suitable for wet spraying and hand application in a wide variety of repair applications, and is particularly well suited to vertical and overhead repairs. Typical applications would include, but not be limited to, the following: Mass infill to large areas Repairs to irregular profiles Excellent for repairs to fire-damaged concrete Fast track repair programmes, where rapid application at high volume is required Single layer, high build applications Advantages Cost effective - shrinkage control enables repairs to be completed „right first time‟. Very low rebound is an additional cost benefit Enhanced durability - works in tandem with extremely low permeability to prolong effective working life Compatibility - aligns performance closer than ever before, to that of host concrete User friendly - specifically developed to provide an easyto-apply product, suitable for local conditions Definable performance - positive benefits are easily demonstrated via a single, simple measurement Description Renderoc SP40 is supplied as a ready to use blend of dry powders, which requires only the addition of clean water to produce a highly consistent, hand and spray grade, repair mortar suitable for most structural and load bearing repairs.

Additional Information:

• Item Code: 40
• Production Capacity: little as 4 months
• Delivery Time: immediately
• Packaging Details: 25kg Renderoc SP40 has a shelf life of 12 months if kept in a dry environment, in its original packing. If stored in conditions of high temperature and/or humidity, the shelf life may be reduced to as little as 4 months

Product Details:

Techoxy 3

TECHOXY-3 is a two component epoxy resin based waterproofing compound. One part is consisting of epoxy resin & the other part with curing agent.

FEATURES/ADVANTAGES

• Penetrates well into the substrates
• Seals porosity & network offine cracks
• Reduces water permeability
• Bonds strongly to all building materials
• Withstands positive waterpressure
• Can be applied on damp surface
• Water dilutable & non-toxic coating

APPLICATION AREAS

• Water tanks
• Can be used in damp walls, undercoat / primer before Techcoat / Tar-o-Thane application on roof & walls
• Hatcheries & aqua farms

Product Details:

 made from E-glass  alkali resistant coating  high tensile strength  dimensionally stable Product is designed to meet main quality requirements and standard for glassfibre meshes:  CE certified since 2013  regularly audited and tested by main European laboratories CSTB, DiBT, TZUS

Product Details:

Application

• Corrugated asbestos roofs.
• Sunken.
• Rejuvenation of existing bituminous membrane – Hessian / HMHDPE based membrane.
• Residential terraces (flat / slope) in substitution of hessian / HMHDPE based membrane. Advantages
• User friendly, Non-toxic, Green product.
• Excellent Waterproofing Characteristics.
• Good crack bridging property
• Cold applied and hence does not require heating.
• Monolithic and Seamless Membrane.
• Excellent bonding to concrete.
• Can be applied on moist surface also.
• Excellent vapour barrier.
• Good flexibility and does not crack on aging

Product Details:

Water Based UV Resistant Elastomeric PU Liquid Membrane: 
ShaliUrethane® BTD is high performance, water based, cold applied, single component elastomeric insitu liquid membrane for waterproofing usually produced in White / Terracotta / Green colour. It may also be supplied in Black colour against specific orders. ShaliUrethane® BTD is UV resistant. However, for better UV resistance, we recommend use of White colour BTD, having SRI Index > 109, thus facilitating considerable saving in energy. ShaliUrethane® BTD forms a seamless monolithic membrane and can be applied on moist surface. It conforms to ASTM C 836 and ASTM D 6083-97a. Use Horizontal / Vertical grades for horizontal / vertical application respectively.

Additional Information:

• Delivery Time: Immediate
• Packaging Details: Bucket

Product Details:

General purpose, non-shrink, cementitious micro-concrete

 Renderoc RG is used for repairs to damaged reinforced concrete elements, particularly where access is restricted and where vibration of the placed material is diffi cult or impossible. It is suitable for various structural strengthening measures such as encasement build-ups, jacketing, piletop encapsulation resin system, etc

Additional Information:

• Delivery Time: IMMEDIATE
• Packaging Details: 25 KG

Product Details:

CICO NO.2 is yellow coloured viscous liquid based on reactive additives and micro particles suspension with anti corrosive properties. This is used as an Integral Cement Waterproofing Compound for Cement Concrete and Mortar. 

Product Details:

Nitoproof 600PF is used to provide continuous, seamless, water and vapour proof membrane for concrete. Typical applications will include roofs, podiums, balconies, planters, floor slabs, suspended floors, patios, bathrooms, inspection pits, swimming pools, bridge decks, foundations, basements and tunnels. 

Additional Information:

• Item Code: 00
• Production Capacity: 2.0 kg/m² for 1.5mm wet film thickness
• Delivery Time: all time immeidate
• Packaging Details: 25kg

Product Details:

It can be applied on concrete and masonry surface and has been designed with good crack bridging abilities. This coat also prevents the reinforcements/ rebars from corrosion.

Product Details:

CICO Tapecrete  RTU is a two pack polymer modified cementitious elastomeric protective and waterproof coating. When it hardens it develops excellent bonding property to most building materials. It is suitable in both interior and exterior building and all other civil engineering applications. Cured film of CICO TAPECRETE RTU prevents dampness in buildings tanks, roofs and other concrete structures permanently.

ADVANTAGES

• Excellent adhesion to sound and prepared surfaces.
• Pre-measured packs – need only mixing. ??? Easy to apply by brush.
• Excellent barrier coating for CO2 , acid gases and chloride ions.
• Non-toxic suitable for contact with drinking water.
• Non-Corrosive to steel or iron, noninflammable.

Product Details:

Single component acrylic polymer for cement based waterproof composite coating membrane- Advantages ?? Non - toxic, non-flammable and user friendly ?? Provides a tough, impermeable waterproof membrane ?? Can be applied by brush, on horizontal and vertical surfaces ?? Excellent adhesion to concrete and masonry surfaces ?? Protects concrete and mortar from natural elements such as wind, rain, sunlight ?? Breathable - allows inside water vapour to escape

Product Details:

CICO NO.3 is high versatile free flowing colorless concrete additives in liquid form. It is used as quick setting cum rapid hardening admixture for concrete and plaster. This is also used as Antifreeze/deicing compound for plain concrete in sub zero climatic conditions.  

Additional Information:

• Production Capacity: 100%
• Delivery Time: immidae
• Packaging Details: 50kg

Product Details:

MASTERCRETE M-81 is a single component 100% acrylic copolymer admixture speciallydeveloped to improve the properties of cementitious compositions. When it is used withcombinations with standard quality of ordinary Portland cement, it enhances the mechanicalproperties such as bonding (adhesion) with various building materials, flexural, compressionand impact strength. It improves the thin section fragility of cement when used as coating.

Product Details:

ECMAGROUT PU F 200 is a hydrophobic, single component, solvent and phthalate free, water-reactive polyurethane injection system. It will react only when it comes in contact with water and when in contact with water it forms a relatively stiff PU foam and stops the leak. ECMAGROUT PU F 200 is a single component product with an additional catalyst making it possible to adjust the reaction time as per the practical situation. As ECMAGROUT PU F 200 can be seen as a temporary seal to achieve a permanent seal an after injection should be done with the ECMAGROUT PU R 420 for an elastic seal or with the ECMAGROUT PU R 440 for a structural seal.

Product Details:

Nitobond SBR Latex

Nitobond SBR(Latex) is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications too.

Main uses

• Modifying and improving bonding of floor toppings, renderings and mortars.
• Repair of worn, damaged and spalled concrete.
• Repair of large cracks.
• Polymer modified floor screeds.
• Waterproof plasters for masonry and slurries.

Advantages

• Simple to use - Single component, gauged as required.
• High - Provides excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Improves -Gives weather resistant mortar with improved durability impermeability to chlorides and other harmful agents.
• Reduces - Provides waterproof screeds, plasters and Permeability slurries.
• Increases - Improved tensile and flexural properties strength allow thin applications.
• Versatile - Compatible with all common hydraulic cements.
• Cost effective - Nitobond SBR (Latex) is economical to use.

Product Details:

TECH-O-THANE PU is a high performance water based cold applied elastomeric coating. This unique single component system is a ready to use material based on PU modified bitumen emulsion.

Additional Information:

• Packaging Details: 20kg

Product Details:

Nitoprime Zincrich, a zinc primer, is supplied as a single component grey-coloured liquid based on metallic zinc and epoxy resins.

Additional Information:

• Item Code: 08
• Production Capacity: 100
• Delivery Time: immiedate
• Packaging Details: 5kg

Product Details:

Two Component clear aliphatic PU Based Coating • Increased UV resistance and decreased yellowing • Anti-Skid Coating for Mineral based substrates • Provides a maintenance free and dust free substrate • Protects the substrate from Environmental exposure. • Provides good Corrosion resistance for the structure. 

Additional Information:

• Item Code: 99
• Production Capacity: 10%
• Delivery Time: immediade
• Packaging Details: 5 kg Pack (A+B)

Product Details:

Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments. The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications.

Additional Information:

• Delivery Time: immidaite
• Packaging Details: 20kg

Product Details:

Elastobar : Waterproofing membrane product from Zydex to stop water leakage in roof, bathroom & walls.

Stretchable membrane for leakage proofing of concrete surfaces

Excellent UV stability

High bonding strength

Water-resistant

Up to 600% elongation

Product Details:

3M™ 500-Series Polyurethane Construction Sealant, Polyurethane Sealant and Polyurethane Adhesive Sealant products are one component, moisture curing products which form permanent elastic bonds. They bond to a wide variety of materials including plastics, metals, fiberglass, and wood. They are formulated to have a wide variety of Shore A hardness, open times, and performance parameters to meet many application needs.

Product Details:

CICO CUREFREE – MWP is a membrane forming, ready to use, white pigmented emulsion of specially blended Acrylic resin, complying with ASTM C 309-86,TYPE-II Common method of curing such as continuous spraying of water on concrete surface and ponding etc. are inconvenient and is also expensive. Evaporation of water from concrete will deprive it of its much needed water for hydration resulting in capillary pores, lower compressive strengths, chipping off on the surface and development of surface cracks. Liquid membrane-forming curing compound is used on the principle that concrete gets enough water from prematured concrete/mortar for uninterrupted hydration after placement.

Additional Information:

• Delivery Time: 2 DAYS
• Packaging Details: 20 Liter & 200 Liter plastic bucket/barrel.

Product Details:

Product Specification Product DescriptionKey Features:

• It is ready to mix a single component product, just add water in the specified proportion and apply.
• It has excellent adhesion properties, no slip is observed on vertical applications.
• Shrinkage cracks are minimized/eliminated due to its self-curing properties.
• Larger quantity of material can be mixed at a time due to its longer pot life.
• The tiled floor can be made available for the foot traffic after 24 hours.
• It is suitable for heavy duty applications with moderate structural movements.
• It is recommended for external cladding.

Recommendation :

• It is used for applications on a cementitious substrate, self-levelling screeds and blocks
• It is suitable for fiber cement boards, gypsum boards and renders for both interior and exterior surfaces.
• It can be effectively used on vinyl tiles, plywood, old tiles (porous and non-porous) and on the wooden floor using weber.tec prime.

Product Details:

Cico Sipel Water Repellent Coating, Packaging Type: Bucket.CICO SIPEL/SIPEL-S is applied on siliceous/mineral surfaces especially on exterior building brickwork, concrete cement/sand rendering, plastering, natural or cast stone. It reduces the phenomenon of efflorescence due to soluble salts in brickwork. It protects the surface from exterior aggression. SIPEL is recommended for burnt clay brick surfaces. SIPEL –S is suitable for all types of substrate surfaces.

Additional Information:

• Delivery Time: immediate

Product Details:

ZycoSil Max is a 100% Reactive Organosilane Nano-Sealer. When applied on a siliceous substrate, it penetrates up to 3-4 mm inside the substrate and becomes an integral part of the structure. It converts the nature of the substrate from hydrophilic to hydrophobic. ZycoSil Max is water dilutable, safe, sprayable and easy to apply. ZycoSil Max acts like a 3-4 mm deep 'skin' (breathable) to your building as against a polymer or paint film that acts like a 'Band-Aid' on your Building. The peel-off issues are eliminated as ZycoSil Max is non-leachable & UV-Resistant. It has a dual property of preventing of ingress of liquid water while allowing moisture vapours to escape.

Additional Information:

• Delivery Time: Immediate

Product Details:

Moisture Insensitive Epoxy Putty for Underwater Repairs and Damp Conditions

 Sikagard®-694 F(I) is a solvent free epoxy resin based putty. It is a moisture insensitive repair material and can be used on damp substrates and underwater applications.

Additional Information:

• Delivery Time: Immediate
• Packaging Details: 8 kg

Product Details:

Zycosil & Zycoprime :
Nanotechnology based waterproofing chemicals from Zydex to prevent water seepage in walls, roof and more.

100% Silane

Water-soluble nanotechnology

Thermal and UV stability

Life: 20+ years

Penetrative in very fine pores and cracks

Reactive & non-leachable

Product Details:

Zycosil & Zycoprime :
Nanotechnology based waterproofing chemicals from Zydex to prevent water seepage in walls, roof and more.

• Acrylic co-polymer compatible with Zycosil+ & Cement
• Seals and Waterproofs fine cracks and porous plaster
• Water-resistant Paint Primer
• Excellent bonding with cement / new plaster on zycosil+ treated surfaces

Product Details:

CICO NO.1 is yellow coloured viscous liquid based on reactive additives and micro particles suspension with anti corrosive properties. This is used as an Integral Cement Waterproofing Compound for Cement Concrete and Mortar.

Product Details:

Acrylic base waterproofing Coating 

ShaliCrete is a multifunctional acrylic polymer emulsion for enhancing properties of concrete, mortar, grout, cement slurry etc. through better bonding, waterproofing and improvement in several other properties. ShaliCrete is used for permanently bonding plaster to ensure durable finish of exterior walls, bonding new concrete to old concrete, making mortar for repairing and for waterproofing. ShaliCrete is highly durable in wet condition as well. 

Additional Information:

• Delivery Time: Immediate
• Packaging Details: 20 Kg

Product Details:

TCSR 555
Two-component solvent free epoxy system for repairing cracked and damaged concrete structures. It is used for bonding of new structural concrete to old concrete, bricks & steel component as it gives excellent bonding properties with various construction surfaces.

Applications

Excellent system for bonding of old to new concrete/mortar, repair old concrete structure and same can be extended further

It is used for crack filling, foundation bolt grouting and patch repair by using quartz sand and powder

Advantages

It has excellent adhesion and strength on various construction substrates and easy to apply due to low mix viscosity.

It has very low shrinkage and high open time.

Storage

Product should be stored in a dry place in their original, properly closed containers at temperature between 2 - 40°C. Partially emptied container should be closed immediately.

Shelf Life

3 Years in unopened containers

Handling precautions

Mandatory and recommended industrial hygiene procedures should be followed whenever our products are being handled and processed. For additional information please consult the corresponding product data sheets and the brochure “Hygienic precautions for handling plastic products”.

Additional Information:

• Delivery Time: immedate